Yamaha 6-100 HP Four-Stroke Outboards manual.
Clymer Marine and PWC manuals are the #1 source for DIY maintenance, troubleshooting and repair. With step-by-step procedures combined with detailed photography and extensive use of exploded parts views, Clymer manuals are a must-have tool for the do-it-yourselfer.
Models
Yamaha 6 HP (Z-A) (2001-2010)
Yamaha 8 HP (V-A) (1997-2013)
Yamaha 9.9 HP (K-Q) (1985-1992)
Yamaha 9.9 HP (R-W) (1993-1998)
Yamaha 9.9 HP (X-H) (1999-2005)
Yamaha 9.9 HP (R-H) (2007-2010)
Yamaha 15 HP (W) (1998)
Yamaha 15 HP (X-H) (1999-2007)
Yamaha 25 HP (W-H) (1988-2005)
Yamaha 40 HP (X-R) (2000-2004)
Yamaha 50 HP (T-C) (1995-2004)
Yamaha 80 HP (X-B) (1999-2003)
Yamaha 100 HP (X-B) (1999-2003)
This Yamaha marine manual is 520 pages.
QUICK REFERENCE DATA
CHAPTER ONE / GENERAL INFORMATION
Manual organization / Notes, cautions and warnings / Torque specifications / Engine operation / Fasteners / Lubricants / Gasket sealant / Galvanic corrosion / Protection from galvanic corrosion / Propellers / Specifications
CHAPTER TWO / TOOLS AND TECHNIQUES
Safety first / Basic hand tools / Test equipment / Service hints / Special tips / Mechanic’s techniques / Specifications
CHAPTER THREE / TROUBLESHOOTING AND TESTING
Test equipment / Troubleshooting preparation / Operating requirements / Starting difficulty / Fuel system component testing / Ignition system testing / Warning system / Starting system / Charging system / Fuses and wire harness / Trim system / Electrical testing / Power head / Cooling system / Gearcase / Specifications
CHAPTER FOUR / LUBRICATION, MAINTENANCE AND TUNE-UP
Lubrication and maintenance / Pre-operational checklist / Post-operational checklist / Routine maintenance / Fuel requirements / Fuel filter service / Engine oil requirements / Oil drain and fill locations / Pumping oil from the engine / Draining oil / Filling the engine with oil / Oil filter / Engine oil and filter change / Oil screen service / Removing carbon deposits from the combustion chambers / Power head anodes / Timing belt and sprocket inspection / Hoses and clamps inspection / Thermostat inspection / Gearcase lubricant / Changing the gearcase lubricant / Gearcase anode inspection / Water pump and impeller inspection / Propeller shaft inspection and lubrication / Swivel tube and tilt tube lubrication / Steering cable lubrication / Trim system fluid level check and change / Starter motor maintenance / Battery maintenance / Throttle and shift linkage lubrication / Tune-up / Compression test / Spark plugs / Valve adjustment / Carburetor adjustment / Ignition timing / Run test / Special maintenance requirements / Submersion / Storage / Corrosion prevention / Specifications
CHAPTER FIVE / SYNCHRONIZATION AND ADJUSTMENT
Fuel system adjustment / Carburetor synchronization / Valve adjustment / Cable and linkage adjustment / Specifications
CHAPTER SIX / FUEL SYSTEM
Servicing the fuel system / Fuel tank / Gloat level (6, 9.9, 25 and 80-100 hp models) / Specifications
CHAPTER SEVEN / ELECTRICAL AND IGNITION SYSTEM
Starting system / Starter motor / Charging system / Ignition system / Warning system / Specifications
CHAPTER EIGHT / POWER HEAD
Flywheel removal and installation / Cylinder head / Cylinder head / Oil pump / Inspection / Power head installation / Bearing selection / Specifications
CHAPTER NINE / GEARCASE AND DRIVE SHAFT HOUSING
Gearcase operation / Gearcase identification / Propeller removal and installation / Gearcase removal and installation / Water pump / Gearcase disassembly and assembly / Inspection / Drive shaft housing removal and installation / Specifications
CHAPTER TEN / REWIND STARTER
CHAPTER ELEVEN / POWER TRIM AND MIDSECTION
Power trim system / Fluid filling and air bleeding / Midsection / Specifications
CHAPTER TWELVE / REMOTE CONTROL
INDEX
WIRING DIAGRAMS
